Why do you need an Oxford Dynamic EQ?

 

Have you tried to control boomy or harsh frequencies using a traditional static EQ but found that you compromised the integrity of the original recording? Then found that writing automation lost you precious time and sounded unnatural? Perhaps you’ve heard that a multiband compressor is the answer but it left you scratching your head?

 

Then the Oxford Dynamic EQ is the tool you need!


There are many scenarios in mixing and mastering where EQ is required, but where the application of static EQ will result in too much or too little change as the signal varies over time. Or, a signal may require compression/expansion in some frequency ranges more than others. Multi-band compression (MBC) is a common solution. However, MBC provides little flexibility over the shape of the processed band and can suffer from static phase distortion. Linear phase MBC requires high processing latency and can exhibit detrimental low frequency artefacts. Many existing dynamic EQs tend to be complex and daunting to use, even for experienced engineers.


The Sonnox Oxford Dynamic EQ solves all these problems, and enables styles of processing and problem solving which are impossible with a conventional EQ or MBC. All accomplished with hallmark Sonnox precision, transparency and musicality. 



Key Features

  • 5 bands of ‘R3 Type 3’ proportional-Q dynamic equalisation with optional shelf type
  • All bands can overlap fluidly without the static phase distortion or low frequency artefacts associated with multi-band compressors
  • Each band can process and/or detect from mono, stereo, mid or side channels
  • Flexible per-band internal/external side chain controls
  • Allows up/down compression and up/down expansion
  • Unique onset detection option for very precise transient processing
  • A clear and informative GUI simplifies the often complex workflows associated with multi-band dynamic plug-in
  • An easy workflow for both mixing and mastering

 

How much will it cost?

£200UKP ex taxes. 


Platform

Oxford Dynamic EQ is available for Native users (AAX Native, Audio Units, VST/VST3), UAD and the AAX HDX platform. It is not available for Waves SoundGrid.


 


FAQ

 

1. Will the Oxford Dynamic EQ ever support Avid HDX hardware DSP systems? 

As of 14th March 2018, Oxford Dynamic EQ is officially supported on the HDX platform. For more information, please read this article.

 

2. I already have a multi-band compressor (MBC), why would I want the Oxford Dynamic EQ?

Have you ever struggled to fix a problem by overlapping (even slightly) two adjacent bands? Assuming you’re given the chance to even try, you’ll appreciate the difficulties in getting a consistent and great sounding result. Even with its steep crossover filters, your MBC will be unable to achieve precise dynamic spectral control

 

3. What advantage does a dynamic EQ have over a regular static EQ?

A static EQ is just that. Set. If you dial in a 5db cut at 1kHz, it’ll be applied irrespective of the level of your incoming signal. Let’s say that you’re only bothered by the 1kHz frequency when the singer is really going for it in a chorus. On one note. If you apply a static EQ, 1kHz is cut all the way through the song and you’ll need to automate your way around the problem.


A dynamic EQ is more kind to your recording, only doing its thing when you need it to. The result is a less processed and more natural sounding. Less is more!

 

4. What makes the Oxford Dynamic EQ different from other dynamic EQs?

  • Dynamic proportional Q response to retain transparency even when applying lots of gain
  • Flexible, intuitive UI to achieve upward/downward compression and upward/downward expansion
  • Onset detection mode to pick out short, percussive events in full mixes or tracks
  • Unlinked side chain options to allow dynamic detection and processing to occur in different frequency ranges
  • Easier to understand and use

 

5. What sources can I make sound especially good by using the Oxford Dynamic EQ plug-in?

While the Oxford Dynamic EQ sounds great on single tracks or buses, here are a few examples of where it shines:

  • Boomy or harsh vocals, guitars and wind instruments can all be smoothed dynamically, and only when required
  • You get faster and more natural sounding results than by using a regular static EQ and lots of automation
  • Mastering
  • The frequency balance of individual tracks or busses can be morphed to allow space for other parts to pop out of the mix
  • Enhance a vocal without affecting side-channel balance
  • Each of the Oxford Dynamic EQs 5 filter bands has the option for mid and side processing